![]() ![]() * See if I could add this without the license upgrade */ * user keyword sends syslog info to ssh or telnet session */ĭescription "Hi Robin, Is anyone going to need your skills?" ĭescription "Connection to Cisco 3620 fa0/1 10.20.1.1" ĭescription "Connection to user/device 10.0.0.13/24" ĭescription "Connection to user/device 10.0.0.x/24 via VLAN 50" ĭescription "Connecton to Future Juniper Switch" ĭescription "Connection to Future Cisco Switch" ĭescription "Connection to USB-Ethernet then to MacBookAir 10.10.100.246/23" ĭescription "Connection to Comcast Modem 10.0.0.26/24" ĭescription "Connection to Cisco 3620 fa0/0 10.30.0.1" I reset the time on 5-2-2015, 7:10pm */Įncrypted-password "$1$.Kw圓nB8$IHVTgcWgqqjRo97tjOorj1" # SECRET-DATAĮncrypted-password "$1$cFcLmPXI$nZC3NQZtv0WztFUTwreaa1" # SECRET-DATAĮncrypted-password "$1$l0Uh4pQW$3VadaIK6OMZ6.eWSN4p6/." # SECRET-DATAĮncrypted-password "$1$zES4Qia2$cw0t/MQzx.7nJu2zcnQcF0" # SECRET-DATA * I am watching the system uptime to see how accuarate the internal clock is. Switch config: (after this is the router run show configuration | no-more ![]() This Juniper router is my 7th router so I want the loopback address to be 7.7.7.7)?Īny light shed on this subject is much appreciated! THIS still resulted in not being able to ping this loopback address from the Juniper switch.ĭoes anyone know what is required to set up a Juniper Router with a simple loopback address that matches the physical router in my lab (i.e. I did try to configure the Group Global loopback and it still did not show groups Now you will need another static VRF route to leak the route 10.0.0. Why is this so mysterious on Juniper? I did searches on the internet and found articles on Group Global loopback configurations, and found people instructing to use a Proxy Arp. What you need is route leaking from VRF into Global Routing Table (you already did) and route leaking from Global Routing Table into VRF. When I ping the Cisco lo0 address of 1.1.1.1 I have success. Just like between my switch and my juniper router these two are connected directly from the switch to the router on a direct link. If you notice in my static config above, I have a route to 1.1.1.1 via 10.40.1.1. I have had no problem setting up multiple Cisco routers with a lo0 address and pinging from my Juniper switch. Here is that show routing-optionsīut I am not able to ping from the switch to the router's lo0 of 7.7.7.7 I set up a static route on my switch to point to next-hop of 10.20.1.3 so the switch would know to go to that address to get to 7.7.7.7. I am able to ping from router to switch using the driectly connected address ![]() I am able to ping from switch to router using the directly connected address ON a EX2200-C switch that is connected to this router the following way: I am able to ping this address from the router itself #run ping 7.7.7.7 successful I am trying to set up a J2350 router with a lo0 interface address 7.7.7.7. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |